Industrial Steam Hose Selection Guide — Temperature, Pressure and Safety

A steam hose is one of the highest-risk hoses on any plant: the wrong hose or the wrong clamp leads directly to burns and downtime. This guide walks through the technical selection criteria step by step.

Short answer

Saturated steam up to 17 bar (about 207 °C): EPDM hose with steel-wire braid to ISO 6134, fitted with steam-rated safety clamps.
Superheated steam or higher temperatures: rubber hose is not suitable; use a flexible metal hose.
Potentially explosive areas: choose a hose with an electrically conductive tube and cover.

Saturated or superheated? The first selection question

Saturated steam is at the boiling temperature that corresponds to its pressure, so once you know the pressure you also know the temperature. Most service steam, tank heating and steam cleaning lines in refineries and petrochemical plants are saturated.

Superheated steam is hotter at the same pressure. Rubber steam hoses are designed and tested for saturated steam, and their life drops sharply in superheated service. If you do not know which type your line carries, ask operations before ordering — it is the single most important item in the enquiry.

Saturated steam pressure–temperature relationship

The table shows saturated steam temperature at common gauge pressures (values rounded from standard steam tables). Read the temperature from your line pressure and choose a hose that covers both.

Gauge pressure (bar)Gauge pressure (psi)Saturated steam temperature (°C)
00100
229134
458152
687165
8116175
10145184
12174192
14203198
17247207

Note: a steam hose's rating is always its steam working pressure and must not be confused with the rating of the same hose on water or air.

Construction of an industrial steam hose

  • Tube: seamless, steam-resistant EPDM. On hoses for hazardous areas the tube is electrically conductive so static charge can dissipate.
  • Reinforcement: one or two high-tensile steel wire braids; the second braid gives higher pressure capacity and better resistance to impact and crushing.
  • Cover: EPDM resistant to steam, weathering and ozone. Many manufacturers use red for steam hose, but colour is not a technical criterion — read the hose branding.
  • Standard: ISO 6134 is the reference standard for rubber hoses and hose assemblies for saturated steam. Class A has a standard cover; class B has an oil-resistant cover.

Full specifications and the pressure of each size are on the industrial steel steam hose page.

Selecting a steam hose in four steps

  1. Define the steam type and maximum line pressure (saturated or superheated, gauge pressure in bar).
  2. Check the temperature in the table above and confirm the hose temperature range covers it.
  3. Size the hose for flow and for the equipment connection. Steam hose is available from 1/2 to 4 inch.
  4. State the site conditions: potentially explosive area (conductivity required), oil contact on the cover (class B) and the length required.

Couplings and clamps: where most incidents happen

Most steam line incidents start at the connection, not in the hose body. Rubber takes a slight set under heat and pressure, so a clamp that was tight on day one loosens after a few heat cycles.

  • Use bolted two-piece safety clamps or crimped couplings designed for steam; ordinary worm-drive clamps are not suitable.
  • Re-tighten bolted clamps after the line first heats up and at every periodic inspection.
  • Steam quick couplings must be of a locking type so they cannot release under pressure.
  • Match the end-fitting thread to the equipment (see JIC, BSP and metric fittings compared).

Installation, inspection and care

  • Drain after use: once steam is shut off, drain the hose. Condensate left inside penetrates the layers on the next cycle and causes cover blistering and ply separation.
  • Bend radius: avoid sharp bends, especially next to the coupling (see hose bend radius guide).
  • Regular visual inspection: blisters or soft spots on the cover, cracks, exposed wire and hose movement at the coupling mean end of life — retire the hose, do not repair it.
  • Pressure testing: test steam hose assemblies before installation and at set intervals (see hose hydrostatic testing).
  • Storage: away from direct sunlight, ozone sources and oil, with no sharp bends.

Frequently asked questions

What temperature and pressure can an industrial steam hose handle?

The steel-braided steam hose we supply is rated for saturated steam up to 17 bar (250 psi) working pressure, which corresponds to about 207–208 °C. Its overall temperature range is −30 to +208 °C.

Is a rubber steam hose suitable for superheated steam?

No. EPDM steam hoses are built for saturated steam. Superheated steam is hotter at the same pressure and degrades rubber much faster. Use a flexible stainless steel (metal) hose for superheated steam.

Can a steam hose also carry hot water?

Yes, which is why it is often sold as a 'hot water and steam hose'. The reverse is not allowed: never use a hot-water hose on steam.

Is an EPDM steam hose suitable for oil or fuel?

No. An EPDM tube is not resistant to mineral oils or fuels. Class B under ISO 6134 only means the cover resists oil splash on the outside; it does not mean oil can be conveyed through it.

What clamps should be used on a steam hose?

Use bolted two-piece safety clamps or crimped couplings designed for steam. Ordinary worm-drive clamps are not suitable for steam lines. Re-tighten bolted clamps after the line first heats up.

Have your steam line specification?

Send the steam type, working pressure and temperature, size, length and coupling type and we will propose the right hose and clamps with a price.

View the industrial steam hose Request a quotation